Nondestructive Testing service providers

Welder Certificate is a document that shows ability of a welder to make a quality weld in a particular welding process. The Certificate also denotes on which type of welding material and which position the welder is able to perform. A full penetration weld can be performed by welder who is qualified for full penetration & fillet. A welder qualified by vertical position (3G) can perform Flat and vertical in production and so on. These qualification ranges are mentioned in the certificates after referring the applicable codes and standards. Welders are qualified for different process individually. Welding process: Shielded Metal Arc Welding (SMAW)- Arc Welding Tungsten Inert Gas Welding (TIG/GTAW)- Arc Welding Metal Inert Gas Welding (MIG)- Arc Metal Active Gas welding (MAG)- Arc Flux Cores Arc Welding (FCAW)- Arc Electric Resistance welding (ERW) and Lot more.. Welding Qualification standards are given in AWS D 1.1 – Structural Welding

Advanced Quality Centre provides Online Course for QA QC With International Certification for Job Introduction: Quality Assurance and Quality Control are departments that plays major role in all industries to ensure delivery of quality products, Quality Assurance is monitoring and documentation of Quality Control Activities, Quality Control is inspection of the components in process. Industries are ready to recruit engineers who are carrying certificates of international standards and having knowledge of the Product standards. We AQC and ISO 9001:2015 certified Training Institute provide training for candidates looking for a successful career and up gradation in the department of Quality Assurance and Quality Control. Certification Course: QA QC Courses have its career scope in almost all the industry involving metal and non metals components. The certificate course’s scope expands to a vast category such as Oil & Gas extraction, Re

Non Destructive Testing is a smart quality control method that is done the components at various stages, on raw materials, after machining and after some period of service. What does this NDT company do? Non Destructing Testing is a little investment which saves a huge amount of money to the manufacturers by avoiding rejection of components due to casting or raw material defects. It is also essential to do NDT after few processing such as welding & heat treatment , as there are possibilities of metal failure due to heat involved in the process. The below are the three stages when NDT shall be involved; Raw material NDT- Casted, formed, Forged or extruded During Processing- Welding NDT, Machining or Heat Treatment After Service – During service /during maintenance checkup It is essential to involve best NDT Inspection Service Company on the job and well experienced and knowledged NDT Technicians for the job. Since the Non Destructive testing is mostly operator

The metallic or non-metallic components manufactured in industries are possibly having various inherent defects few of which are mentioned below: Casting Defects: – Blow holes, Shrinkage, Porosity, Pipes, Inclusions, Cold shut, Mis-run, Hot tears, segregation. To know more in detail about the causes and types of defects click  https://aqcinspection.com/ndt-for-castings/   Welding Defects: – Undercut, Under fill, Lack of fusion , Lack of Penetration, Excess Penetration, Root Concavity of Suck back, Slag Inclusion, Improper weld bead, Overlap, Crater Pipe, Crater Cracks, HAZ Cracks, Weld Longitudinal or transverse crack, Spatters, Arc Strikes and much more. To know more about the causes & identification of defects click  https://aqcinspection.com/welding-inspection-ndt-services/ These defects have to be identified in the initial stages to avoid major loss to the company, by avoiding processing cost losses. So X ray or Radiography Testing done in industries. The discontinuit

PT / LPT Liquid Penetrant Testing inspection  services are carried out for finding Surface defects, on almost any material except very rough or porous surface materials such as poor cast iron material. Advanced Quality Centre  offers India’s best NDT Inspection Service and we are the most trusted and reliable testing company. We provide Die Penetrant Testing Service, both visible and fluorescent method DP testings are carried out. What is Liquid Penetrant Testing? Liquid or Die Penetrant Testing DPT is a surface defect detection method. Penetrant Testing involves pouring die over the perfectly cleaned surface of the material  and the poured die is allowed to penetrate into the defects. The penetrant thus entered the discontinuities are exposed to developer and the developer sucks out the die and visual presents us the defects as bleed out. PT is generally carried out on any raw material, root weld, finished weld, repaired surface, machined surface or any material in servi

Radiography Testing is a volumetric defect detection method, the NDT method can identify any defects in any material and any locations. How are these Radiography Testing services used in NDT inspections? Difference between RT Radiography and X ray Radiography testing uses Gamma ray as a radiation source and it does not require any electrical power source for inspection, X ray uses radiation emitted from an electrical device and it can be switched ON and OFF. Both Gamma rays and X-rays are electromagnetic radiation and are similar. Advanced Quality Centre  offers India’s best NDT Inspection Service and we are the most trusted and reliable Radiography testing company, we provide RT Inspection Service, both Gamma Radiography and X ray. We use IR-192 and CO-60 Source for Gamma Radiography. X ray on Aluminium Casting and Die Casting. We do industrial radiography for Aluminium components using X ray and Gamma Ray , Pressure die casting components with complex structure can

Advanced Quality Centre  offers India’s best NDT Inspection Service and we are the most trusted and reliable testing company. We provide Magnetic Particle Testing – MPI Inspection Service, both visible and fluorescent method. What is Magnetic Particle Testing? Magnetic Particle testing is done by inducing magnetic field in a material and detecting any magnetic flux leakage by sprinkling or flowing magnetic particles (i.e. Ferrous particles ) over the surface. Magnetic flux leakage happens wherever there is a discontinuity and the flux lines tends to go around the discontinuity as they are not able to go through the  discontinuity. What are the materials MPI Testing can be done? MPI can be carried out on ferromagnetic materials only .The materials having base content as ferrous, nickel or cobalt. Can MPI be done on Stainless Steel SS ? MPI can be carried out Stainless Steel –  except Austenitic Stainless  Steel example: SS 316, SS 304, SS 904L . The below are the two ty

What is the defect size accepted in Ultrasonic Testing ? Indications which are identified using any NDT method is accepted or rejected in reference with the standards. The standards which client accepts or the standard which we follow for production  is called as acceptance criteria. Few of the important acceptance criteria are given in this blog.For more detailed understanding of NDT, Ultrasonic testing(UT) inspection services and defects visit us on https://aqcinspection.com/ Acceptance Criteria : ASME Section VIII Division 1 – Pressure Vessel Construction – Ultrasonic Testing (UT) Inspection Services   These Standards shall apply unless other standards are specified for specific applications within this Division. Imperfections which produce a response greater than 20% of the reference level shall be investigated to the extent that the operator can determine the shape, identity, and location of all such imperfections and evaluate them in terms of