How to get Welder Certificate?

Welder Certificate is a document that shows ability of a welder to make a quality weld in a particular welding process.
Welder Certificate
The Certificate also denotes on which type of welding material and which position the welder is able to perform.
A full penetration weld can be performed by welder who is qualified for full penetration & fillet. A welder qualified by vertical position (3G) can perform Flat and vertical in production and so on.
These qualification ranges are mentioned in the certificates after referring the applicable codes and standards.
Welders are qualified for different process individually.

Welding process:

  • Shielded Metal Arc Welding (SMAW)- Arc Welding
  • Tungsten Inert Gas Welding (TIG/GTAW)- Arc Welding
  • Metal Inert Gas Welding (MIG)- Arc
  • Metal Active Gas welding (MAG)- Arc
  • Flux Cores Arc Welding (FCAW)- Arc
  • Electric Resistance welding (ERW) and Lot more..

Welding Qualification standards are given in

  • AWS D 1.1 – Structural Welding Code- Steel.
  • AWS D 1.3 – Sheet metal welding code.
  • AWS D 1.6 – Stain steel Welding
  • ASME section IX – Boiler & pressure vessel/pipelines Arc Welding.
  • ISO 9606-1- International Standard for Arc Welding.

What are the procedures for welder qualification? Or What is the procedure for qualifying a welder?

  • Conclude the range of qualification such as, plate or pipe, thickness, metal grades, pipe diameter, full penetration or fillet.
  • Choose an appropriate WPS – Welding Procedure specification
  • Prepare a test coupon to the required dimension- refer code for dimension
  • Tack welds the test coupon in the required positon with appropriate root gap bevel preparation.
  • Make the welding as told in the WPS
  • Visually inspect the coupon
  • Make a bend test or Radiography( RT) on the test coupon.
  • After clearing the test- the welder is qualified.
For Welder qualification & welding procedure specification (wps) preparation and approval Visit https://aqcinspection.com/ or call 9489342244 or 0422-4342244. To know about AWS visit http://www.aws.org

Comments

Post a Comment

Popular posts from this blog

Discontinuities in Ultrasonic Testing in NDT

Image
 This blog will discuss types of discontinuities that can be evaluated with the ultrasonic testing in NDT method. Discontinuities can be divided into three general categories inherent, processing and service Inherent discontinuities are usually formed when the metal is molten. Inherent wrought discontinuities relate to the melting and solidification of the original ingot before it is formed into slabs, blooms and billets. Inherent cast discontinuities relates to the melting, casting and solidification of a cast article. Usually caused by inherent variables such as inadequate feeding, gating, excessive pouring temperature or entrapped gases. Processing discontinuities are usually related to the various manufacturing process such as machining, forming, extruding, rolling, welding, heat treating and plating. Service discontinuities are related to the various service conditions such as stress, corrosion, fatigue and erosion. During the manufacturing process, many disco
Read more

NDT on Shafts

Image
  Non Destructive Testing,NDT on Shafts is considered essential , because the shafts are mostly made as load bearing structures, any defects such as cracks will propagate more during acting of load and eventually will cause failure. The most possible defects in shafts are Cracks and Pipes , which is shown below The Non Destructive methods preferred for defect detection on raw material shafts are Ultrasonic Testing, Magnetic Particle testing / Eddy Current Testing / Magnetic Flux Leakage method. We have not discussed about other NDT methods such as Liquid Penetrant testing & Radiographic testing because for raw material inspection. These methods will be cost effective for raw material testing  ( i.e. most costly and labor intensive, also there is possibility of missing out the cracks in radiography testing due to orientation of crack ) The Defect wise identification method is given as below  , Internal Defect ( Piping ) – Ultrasonic Testing Surface Defects  (C racks) – Magnetic Part
Read more

Standards for Welding Positions

Image
  Standards for Welding Positions : It is very important for the Weld Inspector  to know the position , or location of a joint relative to the horizon, because it may determine what welding process, methods, and techniques can be used. Welding is usually easiest when the welder can work on a joint located on a flat, horizontal surface, such as on a table or bench. However, joints in the field may be located in a variety of positions relative to the welder and to the horizon, as shown below.  1)  Welding positions – AWS D1.1, European Welding Standard EN 287 – 1, ASME IX: 2) Welding Positions – Butt, Fillet and Piping Welds: Flat Butt Weld Position – 1G In this position, the axis line of the weld must  not incline more than 15°  from the horizon and the face of the weld must be on top. Welders often refer to the flat-position welding by the nonstandard term  downhand welding. Horizontal Butt Weld Position – 2G In this position, both plates are perpendicular to the bench top, but the axi
Read more