NDT Methods Selection

 NDT Method Selection:

The NDT (nondestructive testing) methods are:

 

  1. Visual Inspection – VT
  2. Liquid Penetrant Testing – LT
  3. Magnetic Particle Testing – MT
  4. Radiographic Testing – RT
  5. Ultrasonic Testing – UT
  6. Eddy Current Testing – ET (not used in field inspection)
  7. Acoustic Emission Testing – AET (not used in field inspection)
  8. Phased Array Ultrasonics – PA
  9. Time Of Flight Diffraction – TOFD

Since each NDT methods has its own set of advantages and disadvantages and some are better suited than others for a particular application, the NDT technician or engineer must select the method that will detect the defect or make the measurement with the highest sensitivity and reliability. The cost effectiveness of the technique must also be taken into consideration.

The following table provides some guidance in the selection of NDT methods for common flaw detection and measurement applications.

NDT methods

AQC (Advanced Quality Centre) is an ISO 9001:2015 certified testing centre. We provide world class training and ISO certifications on NDT Non destructive testing course in Coimbatore.  We have a team of highly knowledgeable and professional engineers who trains our students on the NDT course and Welding Course in Coimbatore. Our students get industry standard practical knowledge while pursuing the courses of NDT destructive testing , welding course in Coimbatore or welding inspector course in Coimbatore.  We assure 100% job guidance after completion of every course i.e. welding course in Coimbatore and Welding Inspector Course in Coimbatore and NDT courses in Coimbatore.  We also provide industry standard quality check for industrial materials using NDT in Coimbatore. We are equipped with International standard instruments to perform NDT in Coimbatore using various non destructive testing methods.


AQC is a leading training institute which provides advanced training courses on the Welding course, Welding Inspector course and NDT Course in Coimbatore. Our technical trainers for QA QC courses and  Welding Course are highly knowledgeable and technically trained. We provide the best classroom teaching as well as industry-standard practical knowledge for each course. We also provide a welding inspector course in Coimbatore, where our students get ample knowledge about quality checking of welded joints and eligibility assurance of welders. We stand as Best NDT training institute in TamilNadu and we offer best QA QC courses.


Please feel free to reach us https://aqcinspection.com/training/ to learn more about any of the methods in detail.

Visit our technical and career updates at our Blog site https://advancedqualitycentre.blogspot.com . or

https://ndtcenter.blogspot.com

Location: Advanced Quality Centre,116-B, 5th St Ext, near Kalyan Jewellers, 5th Street Extension, Doctor's Colony, Gandhipuram, Tamil Nadu 641012, India

Comments

Post a Comment

Popular posts from this blog

Discontinuities in Ultrasonic Testing in NDT

Image
 This blog will discuss types of discontinuities that can be evaluated with the ultrasonic testing in NDT method. Discontinuities can be divided into three general categories inherent, processing and service Inherent discontinuities are usually formed when the metal is molten. Inherent wrought discontinuities relate to the melting and solidification of the original ingot before it is formed into slabs, blooms and billets. Inherent cast discontinuities relates to the melting, casting and solidification of a cast article. Usually caused by inherent variables such as inadequate feeding, gating, excessive pouring temperature or entrapped gases. Processing discontinuities are usually related to the various manufacturing process such as machining, forming, extruding, rolling, welding, heat treating and plating. Service discontinuities are related to the various service conditions such as stress, corrosion, fatigue and erosion. During the manufacturing process, many d...
Read more

NDT on Shafts

Image
  Non Destructive Testing,NDT on Shafts is considered essential , because the shafts are mostly made as load bearing structures, any defects such as cracks will propagate more during acting of load and eventually will cause failure. The most possible defects in shafts are Cracks and Pipes , which is shown below The Non Destructive methods preferred for defect detection on raw material shafts are Ultrasonic Testing, Magnetic Particle testing / Eddy Current Testing / Magnetic Flux Leakage method. We have not discussed about other NDT methods such as Liquid Penetrant testing & Radiographic testing because for raw material inspection. These methods will be cost effective for raw material testing  ( i.e. most costly and labor intensive, also there is possibility of missing out the cracks in radiography testing due to orientation of crack ) The Defect wise identification method is given as below  , Internal Defect ( Piping ) – Ultrasonic Testing Surface Defects  (C rac...
Read more

Standards for Welding Positions

Image
  Standards for Welding Positions : It is very important for the Weld Inspector  to know the position , or location of a joint relative to the horizon, because it may determine what welding process, methods, and techniques can be used. Welding is usually easiest when the welder can work on a joint located on a flat, horizontal surface, such as on a table or bench. However, joints in the field may be located in a variety of positions relative to the welder and to the horizon, as shown below.  1)  Welding positions – AWS D1.1, European Welding Standard EN 287 – 1, ASME IX: 2) Welding Positions – Butt, Fillet and Piping Welds: Flat Butt Weld Position – 1G In this position, the axis line of the weld must  not incline more than 15°  from the horizon and the face of the weld must be on top. Welders often refer to the flat-position welding by the nonstandard term  downhand welding. Horizontal Butt Weld Position – 2G In this position, both plates are perpendic...
Read more